Microtest MICROSCANNER Spezifikationen

TMMicroScanner Pro™Users Manual(English)November 2001, Rev. 2, 9/03© 2001-2003 Fluke Corporation. All rights reserved.All product names are trademarks

MicroScanner ProUsers Manual6Operating ModeMODEPress MODE to select the desired test. The availablemodes are:• WIREMAP• OFFICE IDENTIFIER• LENGTH•

MicroScanner Pro™Calibration Mode7If you know a cable’s NVP, change the displayednumbers using the keys until the appropriateNVP is displayed. The

MicroScanner ProUsers Manual8MICROSCANNER PRO TestsThis section describes the tests that you can conductwith MICROSCANNER PRO. WiremapThe Wiremap func

MicroScanner Pro™MicroScanner Pro Tests9Following are examples where MICROSCANNER PRO didnot detect any faults.Full Wiremap with intact shield shown a

MicroScanner ProUsers Manual10Below are examples of wiring faults. The FAULTindicator will be displayed and the numerical wireindicators will blink.Re

MicroScanner Pro™MicroScanner Pro Tests11If the wire does not go to the far end, the numericalindicator for the open will be left blank. The wordOpen

MicroScanner ProUsers Manual12Patch Cable WiremapThe Wiremap function can also be used to verify patchcables.1. Simply plug the two ends of a cable i

MicroScanner Pro™MicroScanner Pro Tests132. To display the length screen, press the MODE keyuntil the word LENGTH appears on the screen. Theoverall c

MicroScanner ProUsers Manual14Some early model 100TX only network equipment doesnot generate link pulses and MICROSCANNER PRO willdisplay HUB, the cab

MicroScanner Pro™MicroScanner Pro Tests15When MICROSCANNER PRO displays Hub and the cablelength, press the MODE key to activate the blinkingHub light.

LIMITED WARRANTY AND LIMITATION OF LIABILITYEach Fluke Networks product is warranted to be free from defects in material and workmanship under normal

MicroScanner ProUsers Manual16MICROSCANNER PRO also Identifies workstations.1. Connect the cable to be tested to the MAIN jack(identified on the unit

MicroScanner Pro™MicroScanner Pro Tests17Pair LengthIf are displayed, you will be able to showdetailed pair information for each standard conductor

MicroScanner ProUsers Manual18Coaxial CablingNoteThis feature is available when you use theCOAX upgrade kit.MICROSCANNER PRO measures the full length

MicroScanner Pro™MicroScanner Pro Tests19If the coaxial cable is not terminated at the far end, theword Open will be displayed.If a shorted cable is d

MicroScanner ProUsers Manual201. Attach the coax adapter to the MAIN jack(identified on the unit right above the modular 8jack).2. To display the O

MicroScanner Pro™Toner21TonerToner is a cable tracing function that assists in trackingcables hidden in walls, ceilings, floors, or patch panelsby gen

MicroScanner ProUsers Manual22Technical SpecificationsDimensions:MICROSCANNER PRO: 13.97 cm x 8.25 cm x 2.54 cm(5.5" x 3.25" x 1")Wirem

MicroScanner Pro™Technical Specifications23Environmental:Operating Temperature: 0° to 50° C (32° to 122° F)Storage Temperature: -10° to 55° C (14° to

MicroScanner ProUsers Manual24

Table of ContentsTitle PageIntroduction...

Length... 12Network Link Indicato

1MicroScanner Pro™IntroductionMICROSCANNER PRO™ is an all-in-one network tester thatyou can use to verify twisted pair and coaxial cables,measure leng

MicroScanner ProUsers Manual2Features• Tests unshielded twisted pair (UTP), shieldedtwisted pair (SSTP) and coaxial cable• Pinpoints opens, shorts,

MicroScanner Pro™Registration3RegistrationRegistering your product with Fluke Networks givesyou access to valuable information on product updates,trou

MicroScanner ProUsers Manual4Contacting Fluke NetworksIf you have technical questions, you may contact FlukeNetworks’ Technical Support by phone, fax

MicroScanner Pro™Battery5BatteryMICROSCANNER PRO requires a 9 Volt Alkaline battery.The Battery icon is displayed on the screen whenMICROSCANNER PRO d